|
|
|
Kto jest w sklepie?
Sklep przegląda 5792 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
SETTING CLOCK RESETTING THE MICROCOMPUTER
Reset microcomputer under the following conditions:
(Main unit operation) Press ON/STAND-BY button to enter the stand-by mode. q To erase all of the stored memory contents (clock and timer
2 1 Press ON/STAND-BY button to enter the stand-by mode. 4 Press TUNING/TIME ( or ) button to select the time
Whilst pressing down button and the second.
(AM 0:00 PM 11:59) STAND-BY
In this example, clock set for q If the display is not correct. 24-hour (0:00) system. Within 5 seconds, press MEMORY/SET button. q If the operation is not correct.
Press the CLOCK button.
1 2 settings, tuner and CD presets).
3
button, hold down the ON/STAND-BY button for at least 1 CLOCK
1,2
2
display mode. "0:00" � The 24-hour display will appear.
ON/ "AM 0:00" � The 12-hour display will appear. TUNING/ TIME ( )
(0:00 23:59)
q The operation explained above will erase all data stored in q Note that this can only be set when the unit is first installed memory including clock timer settings, tuner and CD SET
"AM 12:00" � The 12-hour display will appear. (AM 12:00 PM 11:59) MEMORY/
Caution:
or it has been reset (see page 29). presets.
5 Press the MEMORY/SET button. 6 Press TUNING/TIME ( or ) button to adjust the hour.
q Press the TUNING/TIME ( or ) button once to advance
2 q When the 12-hour display is selected, "AM" will change autoNotes concerning use: the operation becomes erratic. 0.2 6 m minutes. and sensor on the main unit with a soft cloth. (8" 20')
the time by 1 hour. Hold it down to advance continuously. s Remote control
matically to "PM".
7 Press MEMORY/SET button. q Replace batteries the operating distance is reduced or if 8 Press TUNING/TIME ( o r ) button to adjust q Periodically clean transmitter LED on the remote control 3
4 Press TUNING/TIME ( or ) button once advance q Exposing sensor on the main unit to strong light may in1 5
by 1 minute. Hold it down to change time in 5 terfere with operation. Change lighting or the direction of minute intervals. the unit. 1
OPERATION MANUAL
�7�
0:00 AM 12:00 The hour setting will not even if minutes advance q Keep the remote control away from moisture, excessive heat,
"59" to "00". shock, and vibrations.
q The clock starts operating from "0" seconds.
9 Press the MEMORY/SET button. 5
(Seconds are not displayed.)
6
To see the time display:
7
Press the CLOCK button. q The time display will appear for about 5 seconds.
Note: q The clock display will flash on and off at push of the CLOCK button when the AC supply is restored after a power failure occurs or after the AC power lead is disconnected. If this happens, follow procedure below to change the clock time.
8
9
To change the clock time:
xPress the CLOCK button. yWithin 5 seconds, press the MEMORY/SET button. zPerform steps 6 9 above.
To change the time display mode:
xPerform steps 1 2 in the section "RESETTING THE MICRO-
COMPUTER", on page 29.
CD-PC671H/651H
yPerform steps 1 9 above.
|
|
|
> |
|
