|
|
|
Kto jest w sklepie?
Sklep przegląda 6043 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
SETTING THE CLOCK PREPARATION FOR USE
Replace batteries the operating distance is reduced or if Periodically clean transmitter LED on the remote control 24-hour (0:00) system.
CD-C621H
In this example, clock is set for the Within 5 seconds, press the MEMORY/SET button.
1 Press ON/STAND-BY button to enter the stand-by mode. Notes concerning use: (Main unit operation) 2 Press CLOCK button. the operation becomes erratic. 3
0.2 6 m
and sensor on the main unit with a soft cloth.
Press TUNING/TIME ( or ) button to select the time (8" 20')
1 Keep the remote control away from moisture, excessive heat, CLOCK (0:00 23:59) 1 5
4
Exposing sensor on the main unit to strong light may interfere with operation. Change lighting or the direction of the unit. shock, and vibrations. "AM 12:00" � The 12-hour display will appear.
display mode. "0:00" � The 24-hour display will appear. (AM or PM 12:00 11:59)
ON/ STAND-BY TUNING/ "AM 0:00" � The 12-hour display will appear.
SET ( ) Note that this can only be set when the unit is first installed
TIME (AM or PM 0:00 11:59) MEMORY/
or it has been reset.
5 Press the MEMORY/SET button.
2 6 Press TUNING/TIME ( or ) button to adjust the hour. RESETTING THE MICROCOMPUTER 3
If the display is not correct. Press the MEMORY/SET button. Press ON/STAND-BY button to enter the stand-by mode.
Press the TUNING/TIME ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously. Reset microcomputer under the following conditions:
When 12-hour display is selected, "AM" will change autoTo erase all of the stored memory contents (clock and timer
2
matically to "PM". settings, tuner and CD presets).
4 If the operation is not correct.
1,2
7
8 Press TUNING/TIME ( o r ) button to adjust the 1
minutes.
0:00 AM 12:00 Press the TUNING/TIME ( or ) button once to advance 2 Whilst pressing down button and the
5
memory including clock timer settings, tuner and CD Press the MEMORY/SET button.
by minute. Hold it to change time in 5 button, hold down the ON/STAND-BY button for at least 1 minute intervals. second. The hour setting will not even if minutes advance from Caution: "59" to "00". The operation explained above will erase all data stored in
OPERATION MANUAL
�6�
presets.
The clock starts operating from "0" seconds. (Seconds are not displayed.)
9 6
7 Note:
8
In event of a failure or when the AC power lead is disconnected, the clock display will go out. When AC power supply is restored, the clock display will flash on and off to indicate time when the power failure occurred or when the AC power lead was disconnected. If this happens, follow procedure below to change the clock time.
9
To change the clock time:
Press the CLOCK button.
Within 5 seconds, press the MEMORY/SET button.
1 2
Perform steps 6 9 above.
3
To see the time display:
Press the CLOCK button. The time display will appear for about 5 seconds.
To change the time display mode:
Perform steps 1 2 in the section "RESETTING THE MICROCOMPUTER".
1 2
Perform steps 1 9 above.
|
|
|
> |
|
