|
|
|
Kto jest w sklepie?
Sklep przegląda 6043 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
21E-FG3RU
PIF ADJUSTMENT
No. Adjustment point 1 Tuner IFT ( PRESET ) Adjustment condition/procedure 1. Get the tuner ready to receive the CH. E - 9 signal,but with no signal input. Adjust the PLL data. 2. Connect the sweep generator's output cable to the tuner antenna. ( RF SWEEP ) 3. Adjust the sweep generator's to 80dBµV. 4. Connect the response lead ( use LOW IMPEDANCE probe with wave detector ; see Fig.1 ) to the tuner's IF output terminal. ( This terminal must have the probe alone connected ). 5. Set the RF AGC to 0 - 6 V with no saturation with the waveform. 6. Adjust the tuner IF coil to obtain the waveform as shown in Fig. 2. Note: Be sure to keep the tuner cover in position during this adjustment. Waveform or others
No. Adjustment point 1 PURITY ADJ.
PURITY ADJUSTMENT
Adjustment condition/procedure 1. Receive the GREEN-ONLY signal. Adjust the beam current to ~700 µA. 2. Degauss the CRT enough with the degausing coil. Note: Follow the Job Instruction Sheet to adjust the magnetic field. Vertical Bv: +0.030 mT (0.30 gauss) Horizontal Bh: +0.020 mT (0.20 gauss) (Reference: page 7-2) 3. Maintain the purity magnet at the zero magnetic field and keep the static convergence roughly adjusted. 4. Observe the points a, b as shown in Fig. 1-1 through the microscope. Adjust the landings to the A rank requirement. 5. Orient the raster rotation to 0 eastward. 6. Tighten up the deflection coil screws. » Tightening torque: 108 ± 20 N (11 ± 2 kgf) 7. Make sure the CRT corners landing meet the A rank requirements. If not, stick the magnet sheet to correct it. Note: This adjustment must be done after warming up the unit for 30 minutes or longer with a beam current over 700 µA. Note: Set the service mode by JA304 & JA307 (short) then press factory process R/C RGB key to change to RGB mono colour mode. * For the following colours press R/C RGB(Hex 7E) key to change. Waveform or others
a
b
10k
Oscilloscope
1n60
1000p IF OUT
100k
1000p 75ohm
Fig.1
E-9 CH P C
-1.5+/-0.8dB
30mm
Fig. 1-1
30mm
A
Fig.2
B A=B
Fig. 1-2 Rank "A" (on the right of the CRT)
2
RF-AGC TAKE OVER POINT ADJUSTMENT (I2C BUS CONTROL) (AUTO & MANUAL ADJ)
1. Receive "PAL COLOUR BAR" signal. » Signal Strength: 56 ± 1 dBµV (75 ohm open) 2. Connect the oscilloscope to TP201 (Tuner�s AGC Terminal) as shown in Fig. 3-1.
Oscilloscope 0.1V + � Bias box + �
» Bias box: About 4.5 V
* for Auto ADJ 1)Receive �PAL COLOUR BAR� signal. signal strength: 56 ± 1dBµV(75 ohm open) 1)Go to service mode. 2)Go to service data V01, press R/C to operate auto key (Hex C1) and confirm the �OK� display on the screen. 3)If appear NG, increase data some step and pls repeat step 2 again. 4)proceed step 4 & 5 in manual mode.
TP201
A
8
TV Set
GREEN ONLY
BLUE ONLY Signal-colour screen cleared
RED ONLY
B A=B
Fig. 3-1
3. Call "V01" mode in service mode. Adjust the "V01" bus data to obtain the Tuner output pin drop 0.1~1.0V below maximum voltage. 4. Change the antenna input signal to 63~67dBµV, and make sure there is no noise. 5. Turn up the input signal to 90~95 dBµV to be sure that there is no cross modulation beat.
Fig. 1-3
Rank "A" (on the left of the CRT)
* Press R/C RGB key for 1 second in NORMAL MODE, the colour will change to RGB mono colour mode.
8-1
8-2
|
|
|
> |
|
